Sharkbite Fitting Won’t Go On: Reasons And What To Do?

SharkBite products are patented products that are used by homeowners all over the world.

In case you did not know what SharkBite products are, these are devices that are used to join PEX, copper, and CPVC devices without the use of substances such as glue, solder, and so on.

But what happens if the SharkBite fitting won’t go on?

Well, in this article that is exactly what we are going to be talking about. We will be looking at the problems and their solutions.

Possible Problems and Solutions On Why SharkBite fitting Won’t Go?

Sharkbite Fitting

Yes, not all plumbers are fans of SharkBite but here, we will be taking a look at probable problems as well as solutions to those problems.

  • Pipe Not Connected Properly

SharkBite fittings are made to ensure a leak-free seal. When a SharkBite fitting leaks, the first thing you should check is that the pipe is properly connected to the fitting.

You might be able to solve the problem by disconnecting and reconnecting the pipe.

Because SharkBite fittings include small stainless-steel teeth on the inside, you’ll need a specific tool, which can be found at most home improvement stores.

There is another option if you don’t have this tool and don’t want to spend the money on it.

Make sure you have an adjustable wrench on hand. Place your wrench against the cufflink of the fitting and slip it over the pipe you’re trying to remove. Now is the time to put your order.

After you’ve removed the pipe, look for damage on both the outside and inside. You’ll also want to look over the fitting. Replace the pipe in the fitting if nothing appears to be incorrect.

The SharkBite Deburr and Gauge Tool will assist you in deburr and measuring the depth of the pipe, even if you don’t need one. The suggested length to enter your pipe into the fitting for a 12-inch pipe is a 15/16-inch insertion depth.

For precision, it’s preferable to use a permanent marker to mark the length.

If you didn’t know, the end of your pipe must be deburred, polished precisely square, and free of debris before you can install it.

Any of these issues could potentially cause your fitting to have a weak seal, and if you have a weak seal, your fitting will eventually leak water.

  • Painting on Pipes

Painting your pipes is another factor that can result in a poor seal. The dried paint might press against the cufflink part of the fitting, weakening the seal and allowing water to flow.

To remedy the problem, turn off the water in your home and then separate the pipe from the fitting.

After the pipe has been detached, use a quality paint remover to remove all the paint around the pipe’s end. Most home improvement stores offer a diverse selection of products.

Sandpaper also works, but it takes a little more effort. After you’ve removed the paint, re-insert your pipe into the fitting and reconnect your home’s water supply.

  • Distorted Pipe

A distorted pipe is another issue that could be causing your fitting to leak. Your pipes can become distorted over time as a result of normal wear and tear, as well as severe temperatures and abuse.

If you find that your pipes are distorted, you should replace them as soon as possible. When a distorted pipe is placed into a fitting, it will most likely result in a weak seal and water leakage.

  • Misfitting Pipe

If the SharkBite fitting is still leaking, there may be a problem with the fitting itself. Remove and inspect both pipes inserted in the fitting.

Look inside the fitting to see if the ring is damaged or missing. In this case, the fitting will need to be replaced with a new one. Fortunately, however, all SharkBite faucets come with a 25-year limited warranty.

Lastly, this video on SharkBite fittings installation will be a good watch for you.

Final Words

SharkBite fittings have been very revolutionary. But like everything else in the market, these products too incur some issues every now and then. But you should not be scared if you do face any of these issues.

By reading SharkBite fitting won’t go on, you will know the reason behind the problems and their solutions. If you are unable to fix the problems on your own, we recommend hiring a plumber.

Professionals can get the job done more efficiently.

Ralph Wade

Hey...Ralph is here! So, did you find this article useful? If so, please leave a comment and let me know. If not, please tell me how I can improve this article. Your feedback is always appreciated. Take love :)

One thought on “Sharkbite Fitting Won’t Go On: Reasons And What To Do?

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Recent Posts